How To Make a Bouroullec Joyn Desk with IKEA Lagan Countertop

Home Hacks

For my grandfinale, here's a nice knock off of one of my favorite designs of all time: the Bouroullec's Joyn desk system for Vitra. Moving into our new offices I really wanted an upgrade from our old IKEA desks, but didn't have a lot of money and really like the solid wood IKEA countertops we'd been using. This project was completely done by myself from scratch and cost pennies (we reused a lot). Enjoy!

The basic concept here is that when you are starting with a good, solid material you can do ALOT with it. Melamine won't give you this freedom. IKEA's Lagan countertop is solid beech. You can really work it — through cutting, painting and/or staining. I've been building desks out of it for a few years, but this was the first time I attempted a more "high rent" solution.

The Bouroullec's Joyn system is lovely in its simplicity and reads like a big family table that hovers in the air. To get a similar look, I first built one long worktop and then carefully set IKEA's Vika Inge legs back from the edges and end to give it more of an appearance of floating lightly above the floor. I stained the desk white to preserve the natural grain and then painted the legs white to pull it all together.

Here are the instructions for one of the big desks I built. I also include a picture above of a small version.

What You Need

Materials
4 Lagan Countertops — I used 96" and cut them down to 68"
6 Vika Inge Legs
Pickled White Minwax Stain in Matte Finish
Minwax oil based Polyurethane
China White Enamel high gloss paint
Wood Putty
2 Media Grommets

Equipment
Circular Saw
Power Drill
Palm Sander
2½ Grommet drill bit
Spackle Knife

Sandpaper — rough to fine
Plenty of rags (for staining and cleaning)

Instructions

The Top - I used a bunch of old desk tops and a few new, and while heavy, it was pretty easy to cut them all down to 68" and then lay them flat on the floor like puzzle pieces (I had some good help in the form of Bill Skinner from Astech Closets). In order to tie them all together we used the end pieces that had been cut off and drilled these into the bottom like big bandaids. With many screws and three big slabs of wood pulling the four tops together, it worked.

Be careful when cutting the ends. The cleaner and straighter you make the cut, the tighter your tops will fit together in the middle. Put the cut ends in the middle as well, so that the nicer finished edges face outwards.

The Legs - Screwing the six legs into the bottom is pretty easy. Just be sure to place the middle legs right on the seam, so that they support the tops in both directions. I set the legs back 7" from the sides and 10" from the ends.

TURN THE BIG DESK OVER CAREFULLY. It's heavy and you don't want to crack the joints (which are fragile), but you can do it with four people.

Drill your holes at this time for your cord control.

Sanding & Staining - The time consuming bit is sanding and staining. You really want the tops to be as smooth as possible before staining, so a good bit of time was spent using varying grades of sand paper with a palm sander. In the middle where the seam was rough, I used wood putty to fill the gaps and then sanded this down as well. It worked nicely and the putty stains well.

Staining requires more patience and lots of open windows. I recommend finding a green alternative to the toxic stuff I ended up using. To get a really solid white look, I used a rag to apply the stain and followed the directions closely. I applied two coats and let it dry thoroughly between applications and gave it a light sanding in between.

Polyurethaning - Simply follow the directions here and find a green alternative as well. I applied two coats and sanded inbetween to ensure a strong, smooth surface.

Painting the Legs - With the metal legs, I gave them each a light coat of spray primer first and then painted them with a small brush. If you can spray prime your legs first, before attaching, that would be a good idea.

To finish, you want to give the desks one last really light sanding to take off the nicks of dry poly and then drop your plastic grommets into the holes.

Voila! Instead of thousands of dollars, you've got a lovely modern Bouroullec inspired worktop for four people which only cost around $350 (labor not included :-)).


Want more smart tutorials for getting things done around the home?
See all of our Home Hacks tutorials


We're looking for great examples of your own household intelligence too!
Submit your own Home Hacks tutorial or idea here!

Recommended by The Kitchn

Around the Web

Categories

DIY, Desks, How To

Maxwell left teaching in 2001 to start Apartment Therapy as a design business helping people to make their homes more beautiful, organized AND healthy. The website started up in 2004 with the help of his brother, Oliver.

17 Comments