apartment therapy changing the world, one room at a time


How to: Make an extra long curtain rod

032708curtain.jpgOver at one of our favorite blogs, Shelterrific, they recently shared how they created a great extra long curtain rod using inexpensive metal conduit...

 
 

They chose two 10' lengths of conduit, making sure it was the right diameter, and used a connector to join the two pieces together. Then they mounted them to the ceiling with conduit clamps. Check out the post that has detailed photos and step-by-step instructions. Has anyone does this in their home? Any other tips, suggestions?

[ image via Shelterrific ]

Tags

How To..., window coverings, conduit, curtain rod, shelterrific

Related Links

Share

Comments (13)

I made a less elegant version of this with conduit that I support with simple hooks on either end of the rod. Couldn't be bothered to cap off the ends with anything -- but 5 years later and it still isn't bothering me.

posted by babymomma on March 27th 2008 at 11:30am
view babymomma's profile

Years ago, I used chrome plumbing pipe and had the shop thread the ends to accept chromed end caps.

posted by bepsf on March 27th 2008 at 11:37am
view bepsf's profile

I did the same thing. I bought curtain rod holders from West Elm and conduit pipe. Looks great. If you dont see the sides, you dont have to cap off the ends, but if you do, you can usually buy the endcaps where you get the conduit to make it look a little more finished.

posted by katrina58 on March 27th 2008 at 11:49am
view katrina58's profile

I have to admit I am not fond of that look because there's sooooo much window between the panels on either side. It seems that there's a good reason why it's hard to find such long rods.

posted by kimg924 on March 27th 2008 at 12:53pm
view kimg924's profile

Does anyone know where those Matisse-esque curtains are from?

posted by st@cy on March 27th 2008 at 12:56pm
view st@cy's profile

Curtains from Ikea.

posted by miss_m on March 27th 2008 at 1:24pm
view miss_m's profile

I love this idea! We have a super long window that has no room on the side of it. We have been looking forever to find something that would work, this may just be the solution. :)

posted by StylishNest on March 27th 2008 at 1:46pm
view StylishNest's profile

i'm not sure what you mean by conduit, but we did this with plumbing pipe and couplers. it runs across our homemade "stage" so the kids can put on shows. super cheap and no problems with it!

posted by pinko on March 27th 2008 at 2:17pm
view pinko's profile

Rods for sliding doors whatever are one of my pet peeves because they always need a support bracket in the middle, and I am a drapery to one side kind of girl. I have always solved this problem with plumbing pipe because it's rigid enough to span a long distance without needing center support. Conduit is a great idea, too.
I'm presently center-support-free using DIY tensioned wire rope. Mine are exposed, but I've also used the same set up covered by a valance in homes where steel and harware aren't part of the decor.

posted by splatgirl on March 27th 2008 at 2:41pm
view splatgirl's profile

Ikea has a rod ("index") that will go nearly 12 ft. and costs $7 Cdn. I needed to cover a distance of just over 14 ft so I bought two. Each rod has one section with a narrower circumference that slides into the one with the wider circumference. (They have simple rubber or plastic stops to put on the ends, or you can replace those with more decorative ends they also sell.) I took one of the skinnier halves and slid both ends into the two fatter halves. The result is a rod that could probably be stable enough to cover 16 feet or so, and is fine for my 14 ft . At my place, the window goes right to the ceiling so they had to be mounted on the side walls. We used plumbing flanges for that.. very stable, with a u-shaped bracket in the middle attached to the ceiling. That's thin aluminum, and we painted it white. The walls and drapes are white, so it's barely noticeable. The whole thing cost us less than $20 and it's been up for 7 years.

The tricky bit was figuring out how to take the drapes down to wash them because the ends are in flanges screwed to the wall. In fact, all you have to do is slide the middle bit well into one side, enough to give you a separation in the rod so you can slide them off. It's a little weird, but very easy to do. Easy and cheap is always hard to beat!

posted by Joanna D. on March 27th 2008 at 4:45pm
view Joanna D.'s profile

I have a row of windows that are about 13' long in my living room, so about 15 years ago, we bought some 1" copper pipe and a connector and made our own curtain rods. At that time the green verdigris was in style so we sprayed the pipes with vinegar and sprinkled salt on it to get the green look. I am going to sand off the green this summer and then seal the aged looking copper to update the room a bit.
To hang the rods, we picked up some wooden wall brackets and painted them to match the wall and we hang curtains with ring clips.

posted by katcorr2003 on March 27th 2008 at 5:07pm
view katcorr2003's profile

Joanna D, I have the same setup as you and you're right it works great! I left my rods black though. I'm in a rental so I'm going to ask my landlord to buy the contraption off me (or heck, he can just have it... although I'll probably want to practice his own crook ways on him) when I move out since his barely-there dusy blinds didn't cut it for me!

posted by sarahjam on March 27th 2008 at 8:08pm
view sarahjam's profile

The conduit pipe made a great curtain for my daughter's apartment window which is 12.5 feet wide. One thing she does notice now is that she has been getting a lot of interference on her cell phone. Has anyone else had this happen?

posted by keeeka on July 31st 2009 at 9:54pm
view keeeka's profile

Feeds

RSS icon Los Angeles

+ City Feeds